Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
See the difference
Before
After
Before
After
Before
AfterFlashing Repair in Henderson, NV
Flashing is the metal that seals the seams where your roof meets something it can’t cover: a chimney, a wall, a skylight, a vent pipe, or the edge of the roofline itself. When it pulls loose, rusts through, or gets sealed with the wrong material, water finds the gap. Flashing repair in Henderson usually runs $220 to $650 depending on the location and how far the damage has spread, and most jobs we handle are done in a single visit. If you’re seeing a stain on the ceiling after a monsoon or a rust streak down the stucco, call Ridgeline Roofing Co. Henderson at (833) 691-6717 and we’ll send someone out to look at it.
We do this work under our broader Roof Repair service, and flashing is one of the most common calls we get after a hard rain in Henderson. It’s also one of the most commonly botched. A tube of caulk smeared over a rusted chimney pan will hold for one season, maybe two, and then fail exactly where it failed before. Our technicians have up to 10 years of experience, and they’ll tell you the honest version: sometimes the flashing just needs re-securing, sometimes it needs to come off and be rebuilt.
When You Need Flashing Repair
Flashing fails quietly. It doesn’t send shingles sliding into the yard or make a noise you can hear from the kitchen. What it does is let water in behind the roof covering, where it travels along the deck until it finds a place to drip. By the time you see the stain, the water has usually been working for a while. Here’s what we look for, and what you can look for yourself.
- Water stains on the ceiling near a chimney or wall. If the stain is directly below a chimney, a sidewall, or a skylight, flashing is the first thing we check. In Henderson’s older neighborhoods off Water Street and along the streets near downtown, we regularly see chimney flashing that was sealed with mastic twenty years ago and never looked at since.
- Rust streaks or orange stains on the stucco below the roofline. Our dry climate slows rust, but the summer sun bakes flashing constantly. A rusted-through step flashing on a sidewall is one of the most common leaks we find in Henderson.
- Flashing lifted, curled, or pulling away from the wall. High winds during monsoon season can peel back edge metal and counterflashing. Once it’s lifted, water gets behind it instead of running over the top.
- Caulk or sealant where metal should be. If a previous roofer (or a handyman, or you) patched a leaking vent boot with silicone, that patch is a temporary fix. When the caulk cracks and lets go, the leak returns. We see this on a lot of resale homes in Green Valley where quick fixes got the house through inspection.
- Daylight or dark gaps around a skylight or vent pipe. If you can see light or a wet ring where the skylight frame meets the roof, the flashing seal has failed. Vent-pipe boots in particular crack and split after years of sun exposure, and that’s a straightforward repair.
- Loose or missing drip edge along the fascia. Drip edge is flashing too, and when it’s gone, water runs behind the gutter and rots the fascia board instead of clearing the roof.
Our Flashing Repair Process
Flashing repair is not complicated work, but it is careful work. The metal has to be woven in properly with the roof covering, not laid on top of it. Here’s how we handle it.
- Photo-documented inspection. A background-checked technician gets on the roof, photographs the problem area from your actual roof, and shows you what we found. No scary speech in the driveway, no pointing at a picture from some other house.
- Trace the water. Water rarely drips directly below where it enters. We look above and around the stain to find the true entry point, because repairing the wrong spot wastes your money and your time.
- Remove the failed material. Old caulk, dead flashing, rotted sealant, damaged shingles around the penetration. We don’t flash over the top of a failed repair.
- Rebuild the flashing correctly. Step flashing woven into the shingle courses, new counterflashing at the chimney, a fresh vent boot, or a replacement drip edge, depending on what’s there. We install materials from lines we’re authorized on, including IKO and Tamko, so you get proper parts and no substitutions.
- Seal and test. Proper sealant applied correctly, then a water check with a hose on areas we can reach safely.
- Clean up and walk you through it. We photograph the finished work, explain what we did, hand you the invoice. The number on the estimate is the number on the invoice.
Flashing Repair Pricing in Henderson
Flashing repair in Henderson typically costs between $220 and $650, and we quote before we start. Most jobs land in the middle of that range for a standard vent boot or sidewall step flashing. Here’s a rough breakdown of what we see for different work.
| Flashing repair type | Typical price range |
|---|---|
| Vent pipe boot replacement | $220 – $340 |
| Skylight flashing repair | $340 – $560 |
| Chimney flashing rebuild | $440 – $650 |
| Sidewall step flashing repair | $280 – $520 |
| Drip edge replacement (per linear foot) | $8 – $14 |
Several things affect the price. The material matters: a vent boot is quick, but a chimney requires more labor because the counterflashing has to be cut in and tied to the masonry. Access matters too; a low-slope section over a patio is one thing, and a steep second-story pitch is another. If there’s underlying damage, we’ll show you the photos before we do anything. Rotted decking or a rotted fascia board from years of a leaking drip edge needs repair before fresh flashing will hold.
We don’t compete on the lowest bid. We compete on the price holding what we said it would. That’s why most jobs are completed in a single visit and backed by our written 90-Day Done Right Promise: if the work isn’t right, we come back and make it right, no arguing, no paperwork runaround. Estimates are free, and we’ll take a second look at any written estimate you have from another roofer.
- Upfront pricing. The number on the estimate is the number on the invoice.
- Free second opinion on any written estimate. Bring what you’ve got and we’ll go over it with you.
- $50 off any repair over $250. Standing offer, no expiration.
- 5% off for seniors and veterans. Permanent discount, applied where it applies.
Why Flashing Fails in Henderson
A few things make flashing fail faster in Henderson than in many other places. The first is the sun. Our summers pound metal and sealant with intense UV, and flexible sealants that hold for years in cooler climates can crack and lift within a few seasons here. The second is our monsoon pattern: long dry stretches followed by sudden heavy rain and high winds. Flashing that’s sealed but slightly loose tends to seal tighter under light rain and fail completely under a monsoon. The third is the stucco on so many of the homes in Henderson; stucco and flashing meet at the wall, and when that junction isn’t done properly, it’s one of the trickiest leaks we see.
That’s why we inspect carefully before we touch a thing, and why we don’t recommend caulk-only patches on metal joints that have failed structurally. A short-term fix may get you through the season, but if the flashing itself is shot, the leak comes back. We’d rather tell you that up front than take your money twice.
FAQs – Flashing Repair
How much does flashing repair cost in Henderson, NV?
Flashing repair in Henderson typically costs $220 to $650, depending on the type and location. A vent boot replacement sits at the low end; a chimney flashing rebuild runs at the top. Call (833) 691-6717 for an exact quote; estimates are free, and we’ll show you photos from your roof.
Can flashing repair be done the same day?
Most flashing repairs are completed in a single visit, and simple jobs like vent boot replacement are often handled the same day. More involved chimney work may need a scheduled return. Our phones are staffed by a live person 24 hours a day, so you can reach us any time, including nights and weekends.
Is it cheaper to repair flashing or replace the roof?
Repair is almost always cheaper than replacement, and flashing repair is no exception. Localized flashing problems are fixed without touching the sound parts of your roof. We’d only recommend replacement if the flashing failure has led to widespread deck rot or if the roof is near the end of its service life anyway. We’ll tell you honestly which situation you’re in.
Can I just caulk a leaking flashing myself?
Caulk is not a real fix for failed flashing, and on metal joints that have lifted or rusted through, a caulk patch will fail within a season or two in Henderson’s sun. We know the temptation to seal it and forget it, and we understand why, but caulking over a failed joint traps moisture in the process. A trained roofer should look at the flashing itself.
What causes flashing to leak in Henderson?
UV exposure, monsoon wind, and age are the three biggest factors. Our intense sun breaks down sealants, wind lifts edge metal, and older homes often have flashing that was never redone when the last roof was replaced. If your home is 20 or more years old and you’ve never had the flashing inspected, it’s worth having someone look.
Talk to Us About Your Flashing
If you’ve seen a stain, a rust streak, or a gap you’re not sure about, call Ridgeline Roofing Co. Henderson at (833) 691-6717. We’ll come out, photograph what we find, and tell you what needs to happen, with a free estimate and an honest price. Our team has been standing behind roofs in Henderson since 1984, and we’re still here for the long haul. If you want to see what else we do, start with our home page.
Written by the team at Ridgeline Roofing Co. Henderson, serving Henderson.