Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Henderson Owner’s Guide
We replace failed CertainTeed flashing using manufacturer-compatible components, and most residential flashing replacements in Henderson run $285 to $650 installed, depending on the flashing type and how much roofing has to be opened up to do it correctly. Many straightforward replacements are completed the same day you call. We’re an independent roofing contractor, not affiliated with CertainTeed, but we’re an authorized installer of CertainTeed products and know the profile lines well.
Most Henderson owners discover the problem the same way: a brown water stain creeping across a ceiling after a spring wind storm, or a handyman who climbed up to clean gutters and found lifted, rusted, or separated metal at a wall or chimney. Sometimes it’s nothing visible at all, just a musty smell in the garage after a monsoon. Flashing is the metal that seals the joints where your roof meets something else, and when it fails, water doesn’t pour in. It seeps, slowly, for months. By the time you see the stain in Henderson, the damage behind it is often older than the stain.
Which CertainTeed Models This Applies To
CertainTeed flashing isn’t tied to one shingle line the way a spring is tied to one garage door model. It’s a family of accessories that work alongside the shingles: step flashing at sidewalls, counterflashing at chimneys, drip edge at the eaves and rakes, valley metal, and pipe boots. If your Henderson home has CertainTeed shingles (Landmark, Presidential, XT 25, or the older Horizon line), the flashing that came with the original install is almost certainly dimensioned to match those shingle profiles.
The identification gotcha that trips people up: CertainTeed shingle color names and product lines are stamped on the wrapper, not the shingle, so once the crew has left you can’t read the model off the roof. What you can measure is the flashing itself. Step flashing is typically 4 x 4 inch or 5 x 5 inch legs; drip edge comes in standard 2 1/2 inch and 4 inch face sizes; valley metal runs 14 to 20 inches wide. Measure the exposed leg of a failed piece and match those dimensions rather than guessing at a part number.
On the OEM-versus-aftermarket question, we’ll be plain with you. CertainTeed-branded flashing is the cleanest match when the colors and profiles line up, but quality aftermarket coil stock in the correct gauge and finish does the same job, and it’s often what gets used on a partial replacement because the original CertainTeed profile has been discontinued. We install parts from GAF and Owens Corning product lines too when a compatible match serves you better than chasing a discontinued CertainTeed piece.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
- Rust streaks on the metal or the shingles below it. Galvanized steel eventually gives up in Henderson’s dry-then-wet cycle, and the rust tells you the protective coating has already breached. Once rust starts at a fastener, replacement beats patching.
- Lifted or curled step flashing at a sidewall. The metal should lie tight against the wall and lap over the shingle course. When it lifts, it’s usually because the fasteners backed out from thermal movement or the caulk seal failed, and wind-driven rain finds that gap fast.
- Caulk that’s cracked, chalky, or peeling along the flashing edge. Caulk is a maintenance item, not a permanent seal, and in Henderson’s summer heat it can fail within a few years. Cracked caulk is the earliest visible sign that water has a path in.
- Water stains on the ceiling or wall near a chimney, skylight, or where the roof meets an addition. Those are the joints flashing protects. A stain that appears after a hard rain points straight at the flashing above it, not at the shingles.
- Daylight or a draft visible in the attic at a roof-to-wall intersection. That gap is where flashing should be sealing. Seeing light through it means the seal isn’t doing its job, and air and moisture are both getting through.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed prices in Henderson depend mostly on how much of the roof has to be opened to access the flashing. A drip edge replacement runs lower because it’s at the roof edge; a chimney counterflashing replacement runs higher because the flashing has to be woven in and the masonry sealed. Rough line-item ranges:
- Drip edge, straight run: $285 to $425
- Step flashing at a sidewall: $350 to $550
- Chimney counterflashing: $450 to $650
- Valley metal, partial section: $500 to $900
The price we quote is the price you pay. That number covers the material, the labor, removal of the failed piece, and re-sealing the joints. Every job is backed by our 90-Day Done Right Promise, a written workmanship guarantee. If the flashing isn’t right, we come back and make it right, no arguing. We’ll also hand you a written line-item estimate before anyone touches the roof, so you can see exactly what’s being replaced and why.
DIY or Call Us?
Flashing sits at the edge of what a careful homeowner can safely inspect. You can walk the perimeter at ground level with binoculars, check the attic for water stains or daylight, and look at the caulk lines from a ladder you’ve set solidly on flat ground. What you shouldn’t do is climb onto the roof to work on it. Flashing replacement means lifting shingle courses, working at the eave and often at heights above a story, and one slip on a sun-baked Henderson roof ends badly. This is real roof-edge work and we treat it that way.
Where DIY goes wrong even for a confident homeowner is the sealing detail. Flashing has to lap in a specific order so water sheds over the layers, not under them, and the fasteners have to land where the next course covers them. Get the lap wrong and you’ll chase a leak for years. Call (833) 691-6717 and we’ll send a background-checked technician in uniform to look, with photos from your actual roof so you can see what we see. A live person answers, day or night.
FAQs
Most flashing lasts 15 to 25 years, but Henderson’s climate shortens that for the galvanized pieces. The dry heat and intense sun degrade the protective coating faster than in wetter climates, and the summer monsoon then finds every exposed fastener. Metal that’s still solid at 20 years is common; caulk seals at the joints often need attention in under a decade. Call (833) 691-6717 and we’ll tell you what your flashing has left.
Sometimes, yes. If the metal is still sound and the failure is a lifted edge or failed caulk, we can re-seal and re-fasten it for a fraction of a replacement. If the metal is rusted through, deformed, or has been sealed over so many times the layers are failing, replacement is the honest answer. We’ll show you the difference with photos. Estimates are free, so call (833) 691-6717.
A single flashing section is usually a few hours, and most of our Henderson jobs are done in a single visit. Chimney counterflashing and valley sections that require opening more of the roof can run into a full day. Weather is the one variable we won’t rush; we won’t seal flashing that’s wet. Call (833) 691-6717 to schedule and we’ll give you a realistic window, not a promise we can’t keep.
We measure your existing flashing dimensions and match gauge, finish, and color to what’s compatible with your CertainTeed shingle profile, pulling from the manufacturer lines we’re authorized for, including CertainTeed, GAF, and Owens Corning. When the exact original CertainTeed piece has been discontinued, we’ll source a compatible equivalent and tell you plainly what we’re substituting before we do it. Call (833) 691-6717 for a free estimate.
Written by the team at Ridgeline Roofing Co. Henderson, serving Henderson and nearby areas.