A Ridgeline company - serving Henderson, NV

Owens Corning Ridge Vent Installation in Henderson, NV

Owens CorningOwens Corning
Architectural shinglesArchitectural shingles
Metal roofingMetal roofing
Tile roofingTile roofing
GAFGAF
Flat & low-slopeFlat & low-slope
Every visit starts with

Free roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation

We have financing partners for your new roof*On approved credit; ask us about your options
Get your free estimate

Owens Corning Ridge Vent Installation: The Henderson Owner’s Guide

Owens Corning-compatible ridge vent installation in Henderson typically runs $340 to $750 installed for a standard single-family roof, and most jobs are completed in a single visit. The estimate is free, the price is written, and the number on the estimate is the number on the invoice. If your ridge vent is the part that has failed, you’ve probably noticed it the way most Henderson owners do: dark streaking on the attic sheathing, a shingle edge lifted along the ridge line, or a ceiling stain that appeared after a monsoon. We install ridge vent systems across Henderson on Owens Corning roofs and match the vent to what is actually up there, not to whatever is closest on a shelf.

Call (833) 691-6717

Which Owens Corning Models This Applies To

Ridge vent is one of the few Owens Corning roof components where the model question is mostly about profile and shingle type, not a serial number. Owens Corning makes shingles (Duration, Oakridge, TruDefinition lines) and a range of roof ventilation and accessory components that pair with them. The vent itself has to match three things: the shingle profile sitting over it, the deck thickness at the ridge, and the net free ventilation area the attic actually needs.

Here is the part most homeowners won’t hear from a phone quote. Owens Corning ridge vent products are specified in net free area per linear foot, and the number matters. A vent rated too low for your attic volume is worse than no upgrade at all, because it lets the house breathe just enough to feel handled while the sheathing above the vent stays wet. On a typical Henderson home with a hip-and-ridge layout, we measure ridge length and attic square footage before we name a product. We are an independent installer and not affiliated with Owens Corning. We are an authorized installer of Owens Corning alongside GAF and CertainTeed, so we aren’t married to one line. If an aftermarket vent matches your shingle profile and ventilation numbers and costs less, we’ll say so.

To identify what you have, check the shingle wrapper in the garage or attic (owners often keep one), measure the ridge length, and look at whether the ridge has a shingle-over vent (low profile, shingles on top) or a hard-plastic louvered vent screwed down. A shingle-over setup and a louvered strip are not interchangeable, and the wrong one means the shingles won’t lay flat.

Explore

Styles & brands we work with

  • Architectural shingles
  • Metal roofing
  • Tile roofing
  • GAF
  • Owens Corning
  • Flat & low-slope

Signs Your Owens Corning Ridge Vent Installation Is Failing

Ridge vents don’t fail by cracking the way a pipe does. They fail slowly, and the evidence shows up in the attic before it shows up in the living room.

  • Streaking or dark bands on attic sheathing. That’s moisture condensing where hot attic air meets the cooler underside of the deck. It usually means the vent’s net free area has dropped below what the attic needs, often because the filter material under the vent has clogged with dust and desert grit.
  • Nails backing out or screws lifted along the ridge cap. In Henderson’s summer heat, shingle sealant softens and the vent strip underneath shifts. Once the fasteners walk, wind gets under the ridge and the whole cap starts to open.
  • Interior ceiling stains near the ridge line. A ridge vent that has lost its seal, or one installed without the proper end caps, funnels water straight into the attic along the ridge. That stain shows up at the top of the ceiling, not the middle, which is a tell.
  • Visible daylight in the attic along the ridge. Look up. A thin line of light in the right place is normal ventilation. A wide gap or a flapping filter material is not, and it’s admitting wind-driven rain during a monsoon.
  • Hot attic temperatures and higher cooling bills. If the attic is cooking in July, the vent may be technically present but ineffective. Blocked soffit intake is often the real culprit, but a clogged ridge vent completes the picture.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing for Owens Corning-compatible ridge vent on a standard Henderson home falls in the ranges below. These are ranges, not quotes. Ridge length, roof pitch, shingle profile, and how much ridge cap has to be removed and reinstalled all move the number.

Item Typical Range
Ridge vent replacement, standard single-family roof (up to ~40 linear ft) $340 – $750
Extended ridge runs or complex hip-and-ridge layouts $750 – $1,150
Ridge vent plus ridge cap shingle rework Quoted after inspection
Airflow check and attic ventilation assessment Included with estimate

The parts-plus-labor breakdown is written on the estimate so you can see what you’re paying for the vent and what you’re paying for the work. There are no surprise line items and no change orders for the standard job. Every installation carries the 90-Day Done Right Promise, a written workmanship guarantee with no arguing and no paperwork runaround. If it isn’t right, we come back and make it right.

DIY or Call Us?

Replacing a ridge vent means being up on your roof at the highest point with the shingles peeled back, on a pitch that gets hot enough in Henderson July to cause second-degree burns through clothing. That’s the honest reason we don’t recommend it. A ladder slip on a 6/12 pitch is not recoverable, and this is also the part that introduces or excludes water at the ridge, so a mistake shows up months later as a ceiling stain.

What an owner can safely do from the ground or with binoculars: look for lifted or missing ridge cap, check the attic for daylight and sheathing streaks, and confirm the soffit vents aren’t blocked. Same-day availability exists on many of these jobs. We’re an authorized Owens Corning installer and can match your shingle profile without substitution. Call (833) 691-6717 for a free, written estimate.

FAQs

Need Roofing help nationwide? Licensed & insured · free written estimates
Call (833) 691-6717
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - Ridgeline Roofing Co. Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch